ORING .3/.437"ID/OD NEO80 0.07" NEOPRENE 80
1407-0031
VICTOR
ORING W NEOPRENE 80 .3"ID; .437"OD; .07" UPC: 716352081450
PRODUCT DESCRIPTION
Neoprene Oriing made out of NEOPRENE 80
This O-ring is made of black Aflas (fluoroelastomer) and has a durometer of 80A. It has a round cross-section and can be used across a wide temperature range (25 degrees F/-3.8 degrees C to 450 degrees F/232 degrees C). Designed for use in a wide variety of sealing applications; this Aflaz O-ring meet standards defined by Aerospace Standard AS568A; which is the Aerospace Size Standard for O-rings.
Aflas (fluoroelastomer) is resistant to oil; heat; electricity; abrasion and many chemicals including strong acids and bases. It is also performs well in all-weather; ozone; and steam applications; although it performs poorly in aromatic hydrocarbons or ketones.
The durometer hardness of this Aflas O-ring is 80A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100; a value of 0 indicates that a sample was completely penetrated; while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale; which is either shore A or D. Shore A is used for softer plastics; while shore D is used for harder plastics.
O-rings provide a pressure and fluid seal between cylindrically shaped; overlapping mating surfaces and are commonly seen in engines; faucets; flanges; valves; and various cylinders. They are circular in shape; with a round cross section; and a hole in the center; similar to a doughnut. O-rings are available in various AS568A dash sizes; which is the standardized sizing for O-rings; and defines the nominal inside diameter (ID); outer diameter (OD); and cross-sectional (CS) diameter of an O-ring.
PRODUCT ATTRIBUTES
Made of black Aflas (fluoroelastomer) for use with a variety of chemicals and applications
Durometer (hardness) of 80A for resistance to penetration
Round cross-section provides a seal between cylindrical overlapping surfaces
For use across a wide temperature range from 25 degrees F/-3.8 degrees C to 450 degrees F/232 degrees C
Meets standards defined by Aerospace Standard AS568A
Neoprene Oriing made out of NEOPRENE 80
TECHNICAL SPECIFICATIONS
Material : Neoprene 80
Part Type : ORING
Gas Service : FUEL;OXYGEN; AIR.
Product Weight : 0.1 lbs
Shipping Weight : 1 lb
VICTOR
ORING W NEOPRENE 80 .3"ID; .437"OD; .07" UPC: 716352081450
PRODUCT DESCRIPTION
Neoprene Oriing made out of NEOPRENE 80
This O-ring is made of black Aflas (fluoroelastomer) and has a durometer of 80A. It has a round cross-section and can be used across a wide temperature range (25 degrees F/-3.8 degrees C to 450 degrees F/232 degrees C). Designed for use in a wide variety of sealing applications; this Aflaz O-ring meet standards defined by Aerospace Standard AS568A; which is the Aerospace Size Standard for O-rings.
Aflas (fluoroelastomer) is resistant to oil; heat; electricity; abrasion and many chemicals including strong acids and bases. It is also performs well in all-weather; ozone; and steam applications; although it performs poorly in aromatic hydrocarbons or ketones.
The durometer hardness of this Aflas O-ring is 80A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100; a value of 0 indicates that a sample was completely penetrated; while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale; which is either shore A or D. Shore A is used for softer plastics; while shore D is used for harder plastics.
O-rings provide a pressure and fluid seal between cylindrically shaped; overlapping mating surfaces and are commonly seen in engines; faucets; flanges; valves; and various cylinders. They are circular in shape; with a round cross section; and a hole in the center; similar to a doughnut. O-rings are available in various AS568A dash sizes; which is the standardized sizing for O-rings; and defines the nominal inside diameter (ID); outer diameter (OD); and cross-sectional (CS) diameter of an O-ring.
PRODUCT ATTRIBUTES
Made of black Aflas (fluoroelastomer) for use with a variety of chemicals and applications
Durometer (hardness) of 80A for resistance to penetration
Round cross-section provides a seal between cylindrical overlapping surfaces
For use across a wide temperature range from 25 degrees F/-3.8 degrees C to 450 degrees F/232 degrees C
Meets standards defined by Aerospace Standard AS568A
Neoprene Oriing made out of NEOPRENE 80
TECHNICAL SPECIFICATIONS
Material : Neoprene 80
Part Type : ORING
Gas Service : FUEL;OXYGEN; AIR.
Product Weight : 0.1 lbs
Shipping Weight : 1 lb
In stock
Only 17 left
SKU
VIC-1407-0031
TTD13.50
1407-0031
VICTOR
ORING W NEOPRENE 80 .3"ID; .437"OD; .07" UPC: 716352081450
PRODUCT DESCRIPTION
Neoprene Oriing made out of NEOPRENE 80
This O-ring is made of black Aflas (fluoroelastomer) and has a durometer of 80A. It has a round cross-section and can be used across a wide temperature range (25 degrees F/-3.8 degrees C to 450 degrees F/232 degrees C). Designed for use in a wide variety of sealing applications; this Aflaz O-ring meet standards defined by Aerospace Standard AS568A; which is the Aerospace Size Standard for O-rings.
Aflas (fluoroelastomer) is resistant to oil; heat; electricity; abrasion and many chemicals including strong acids and bases. It is also performs well in all-weather; ozone; and steam applications; although it performs poorly in aromatic hydrocarbons or ketones.
The durometer hardness of this Aflas O-ring is 80A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100; a value of 0 indicates that a sample was completely penetrated; while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale; which is either shore A or D. Shore A is used for softer plastics; while shore D is used for harder plastics.
O-rings provide a pressure and fluid seal between cylindrically shaped; overlapping mating surfaces and are commonly seen in engines; faucets; flanges; valves; and various cylinders. They are circular in shape; with a round cross section; and a hole in the center; similar to a doughnut. O-rings are available in various AS568A dash sizes; which is the standardized sizing for O-rings; and defines the nominal inside diameter (ID); outer diameter (OD); and cross-sectional (CS) diameter of an O-ring.
PRODUCT ATTRIBUTES
Made of black Aflas (fluoroelastomer) for use with a variety of chemicals and applications
Durometer (hardness) of 80A for resistance to penetration
Round cross-section provides a seal between cylindrical overlapping surfaces
For use across a wide temperature range from 25 degrees F/-3.8 degrees C to 450 degrees F/232 degrees C
Meets standards defined by Aerospace Standard AS568A
Neoprene Oriing made out of NEOPRENE 80
TECHNICAL SPECIFICATIONS
Material : Neoprene 80
Part Type : ORING
Gas Service : FUEL;OXYGEN; AIR.
Product Weight : 0.1 lbs
Shipping Weight : 1 lb
VICTOR
ORING W NEOPRENE 80 .3"ID; .437"OD; .07" UPC: 716352081450
PRODUCT DESCRIPTION
Neoprene Oriing made out of NEOPRENE 80
This O-ring is made of black Aflas (fluoroelastomer) and has a durometer of 80A. It has a round cross-section and can be used across a wide temperature range (25 degrees F/-3.8 degrees C to 450 degrees F/232 degrees C). Designed for use in a wide variety of sealing applications; this Aflaz O-ring meet standards defined by Aerospace Standard AS568A; which is the Aerospace Size Standard for O-rings.
Aflas (fluoroelastomer) is resistant to oil; heat; electricity; abrasion and many chemicals including strong acids and bases. It is also performs well in all-weather; ozone; and steam applications; although it performs poorly in aromatic hydrocarbons or ketones.
The durometer hardness of this Aflas O-ring is 80A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100; a value of 0 indicates that a sample was completely penetrated; while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale; which is either shore A or D. Shore A is used for softer plastics; while shore D is used for harder plastics.
O-rings provide a pressure and fluid seal between cylindrically shaped; overlapping mating surfaces and are commonly seen in engines; faucets; flanges; valves; and various cylinders. They are circular in shape; with a round cross section; and a hole in the center; similar to a doughnut. O-rings are available in various AS568A dash sizes; which is the standardized sizing for O-rings; and defines the nominal inside diameter (ID); outer diameter (OD); and cross-sectional (CS) diameter of an O-ring.
PRODUCT ATTRIBUTES
Made of black Aflas (fluoroelastomer) for use with a variety of chemicals and applications
Durometer (hardness) of 80A for resistance to penetration
Round cross-section provides a seal between cylindrical overlapping surfaces
For use across a wide temperature range from 25 degrees F/-3.8 degrees C to 450 degrees F/232 degrees C
Meets standards defined by Aerospace Standard AS568A
Neoprene Oriing made out of NEOPRENE 80
TECHNICAL SPECIFICATIONS
Material : Neoprene 80
Part Type : ORING
Gas Service : FUEL;OXYGEN; AIR.
Product Weight : 0.1 lbs
Shipping Weight : 1 lb
| SKU | VIC-1407-0031 |
|---|---|
| Weight | 0.000000 |
| Manufacturer | VICTOR TECHNOLOGIES |
Write Your Own Review
Payment Plan:
The items you need are well within your reach. ShopSSLTT has the premium products you want at affordable prices and with our shop now pay later payment plans we make them accessible to all. Lear more on the following links
Payment plan Details : You can now finance your purchases with flexible payment plans. Click here to learn how.
Requirements: Before you apply for the plan make sure you have all the required documents, click here to see the list of documents required.
